RFID working with Arduino UNO but not with Arduino Mega 2560

Question

I am new to arduino and recently encountered this problem. I got a starter kit and in that had an RFID module. I tried using it with the arduino they provided me, but it didn't seem to work. Here is the code if you want to see it.

/*
 * --------------------------------------------------------------------------------------------------------------------
 * Example sketch/program showing how to read data from a PICC to serial.
 * --------------------------------------------------------------------------------------------------------------------
 * This is a MFRC522 library example; for further details and other examples see: https://github.com/miguelbalboa/rfid
 * 
 * Example sketch/program showing how to read data from a PICC (that is: a RFID Tag or Card) using a MFRC522 based RFID
 * Reader on the Arduino SPI interface.
 * 
 * When the Arduino and the MFRC522 module are connected (see the pin layout below), load this sketch into Arduino IDE
 * then verify/compile and upload it. To see the output: use Tools, Serial Monitor of the IDE (hit Ctrl+Shft+M). When
 * you present a PICC (that is: a RFID Tag or Card) at reading distance of the MFRC522 Reader/PCD, the serial output
 * will show the ID/UID, type and any data blocks it can read. Note: you may see "Timeout in communication" messages
 * when removing the PICC from reading distance too early.
 * 
 * If your reader supports it, this sketch/program will read all the PICCs presented (that is: multiple tag reading).
 * So if you stack two or more PICCs on top of each other and present them to the reader, it will first output all
 * details of the first and then the next PICC. Note that this may take some time as all data blocks are dumped, so
 * keep the PICCs at reading distance until complete.
 * 
 * @license Released into the public domain.
 * 
 * Typical pin layout used:
 * -----------------------------------------------------------------------------------------
 *             MFRC522      Arduino       Arduino   Arduino    Arduino          Arduino
 *             Reader/PCD   Uno/101       Mega      Nano v3    Leonardo/Micro   Pro Micro
 * Signal      Pin          Pin           Pin       Pin        Pin              Pin
 * -----------------------------------------------------------------------------------------
 * RST/Reset   RST          9             5         D9         RESET/ICSP-5     RST
 * SPI SS      SDA(SS)      10            53        D10        10               10
 * SPI MOSI    MOSI         11 / ICSP-4   51        D11        ICSP-4           16
 * SPI MISO    MISO         12 / ICSP-1   50        D12        ICSP-1           14
 * SPI SCK     SCK          13 / ICSP-3   52        D13        ICSP-3           15
 */

#include <SPI.h>
#include <MFRC522.h>

#define RST_PIN         9          // Configurable, see typical pin layout above
#define SS_PIN          10         // Configurable, see typical pin layout above

MFRC522 mfrc522(SS_PIN, RST_PIN);  // Create MFRC522 instance

void setup() {
    Serial.begin(9600);     // Initialize serial communications with the PC
    while (!Serial);        // Do nothing if no serial port is opened (added for Arduinos based on ATMEGA32U4)
    SPI.begin();            // Init SPI bus
    mfrc522.PCD_Init();     // Init MFRC522
    mfrc522.PCD_DumpVersionToSerial();  // Show details of PCD - MFRC522 Card Reader details
    Serial.println(F("Scan PICC to see UID, SAK, type, and data blocks..."));
}

void loop() {
    // Reset the loop if no new card present on the sensor/reader. This saves the entire process when idle.
    if ( ! mfrc522.PICC_IsNewCardPresent()) {
        return;
    }

    // Select one of the cards
    if ( ! mfrc522.PICC_ReadCardSerial()) {
        return;
    }

    // Dump debug info about the card; PICC_HaltA() is automatically called
    mfrc522.PICC_DumpToSerial(&(mfrc522.uid));
}

I tried using it with my arduino mega, but when I went to open up the serial monitor, here is what it said:

Firmware Version: 0x0 = (unknown) 
WARNING: Communication failure, is the MFRC522 properly connected?
Scan PICC to see UID, SAK, type, and data blocks...

But when I use my arduino uno it says the following:

Firmware Version: 0x92 = v2.0
Scan PICC to see UID, SAK, type, and data blocks...

And it works just fine! Is there something wrong with the arduino mega, or is there an obvious solution.

Thanks

Marcos G. Marcos G. · Accepted Answer · 2019-07-21T05:36:53

The code you're using is taylored to UNO; for MEGA you need to change the defines for the pins:

#define RST_PIN 9 // Configurable, see typical pin layout above 
#define SS_PIN 10 // Configurable, see typical pin layout

For MEGA, change those values, RST to 52 and SS to 53.

You also need to change your wiring accordingly.

RFID working with Arduino UNO but not with Arduino Mega 2560

1 Answers