STM32F3 Discovery - Implement GPIO-Interrupt

Question

I want to implement a GPIO-Interrupt, but I dont know how, I also found no real sample or explaination for it.

I already know how to write to Pins, but not much more, please consider that I dont really have any knowlegde about c or programming microcontrollers.

A simple example or explaination would help me alot. The following code is what I already have, but I am not sure if this is correct.

GPIO_InitTypeDef   GPIO_InitStructure;
GPIO_InitStructure.Pin = GPIO_PIN_2;
GPIO_InitStructure.Mode = GPIO_MODE_IT_RISING;
GPIO_InitStructure.Pull = GPIO_PULLUP;
GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;

HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);

HAL_GPIO_WritePin(GPIOA, GPIO_PIN_2, GPIO_PIN_SET);

Bence Kaulics Bence Kaulics · Accepted Answer · 2016-10-15T16:32:00

Since @Mouin has described the steps for you and you are using HAL already, here is how to execute those steps, so the way to configure it by using STM32CubeMX software provided by ST Microelectronics. (Note: Browsing that link is recommended as there are many-many examples for the STM32 family, STM32CubeF3 package for example.)

So in brief download it, create a new project for an STM32F3 Discovery board.

On the Pinout tab, the MCU will be shown with all its pins. Just click on a pin and select a functionality you want. In your case GPIO_EXTI2 on PA2 pin:
Now switch to do Configuration tab, and in the last column called System, click on the GPIO button. Available options can be seen on the image below:
Next step is to enable the corresponding interrupt. To do so close the Pin Configuration window and from the System column, click on the NVIC button. If you remember, the EXTI2 has been chosen on PA2 so tick the Enable checkbox for EXTI line2. You can set the priorities here as well.

Everything is ready, click on the Generate source code based on user settigns button → . Following source files will be genereted:

GPIO configuration in gpio.c:

  GPIO_InitTypeDef GPIO_InitStruct;

  /* GPIO Ports Clock Enable */
  __GPIOA_CLK_ENABLE();

  GPIO_InitStruct.Speed = GPIO_SPEED_LOW;

  /*Configure GPIO pin : PA2 */
  GPIO_InitStruct.Pin = GPIO_PIN_2;
  GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  /* EXTI interrupt init*/
  HAL_NVIC_SetPriority(EXTI2_TSC_IRQn, 0, 0); // <--- This and
  HAL_NVIC_EnableIRQ(EXTI2_TSC_IRQn); // <--- this are what were missing for you.

Interrupt service rutine in the stm32f3xx_it.c:

/**
* @brief This function handles EXTI line2 and Touch Sense controller.
*/
void EXTI2_TSC_IRQHandler(void)
{
  /* USER CODE BEGIN EXTI2_TSC_IRQn 0 */

  /* USER CODE END EXTI2_TSC_IRQn 0 */
  HAL_GPIO_EXTI_IRQHandler(GPIO_PIN_2);
  /* USER CODE BEGIN EXTI2_TSC_IRQn 1 */

  /* USER CODE END EXTI2_TSC_IRQn 1 */
}

This is what will be called when an interrupt is triggered, it will call an IRQ handler for the GPIO2 and if everything is fine, the following callback will be called. You have to write your handler code here.

/**
* @brief Interrupt callback for GPIOs
*/
void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
{
    if ( GPIO_Pin == GPIO_PIN_2)
    {
        // Write your code here
    }
}

You have to add the previous part manually (the callback), it has a weak declaration only but won't be generated. You can place it in the stm32f3xx_it.c .

If you want to learn more about the MCU, open up the reference manual and read the GPIO and NVIC section to know how it is done on register level.

STM32F3 Discovery - Implement GPIO-Interrupt

2 Answers