8
votes

Suppose I have data that depends on 4 variables: a, b, c and d. I want interpolate to return a 2D array which corresponds to a single value of a and b, and an array of values for c and d. However, The array size need not be the same. To be specific, my data comes from a transistor simulation. The current depends on 4 variables here. I want to plot a parametric variation. The number of points on the parameter is a lot less than the number of points for the horizontal axis.

import numpy as np
from scipy.interpolate import interpn
arr = np.random.random((4,4,4,4))
x1 = np.array([0, 1, 2, 3])
x2 = np.array([0, 10, 20, 30])
x3 = np.array([0, 10, 20, 30])
x4 = np.array([0, .1, .2, .30])
points = (x1, x2, x3, x4)

The following works:

xi = (0.1, 9, np.transpose(np.linspace(0, 30, 4)), np.linspace(0, 0.3, 4))
result = interpn(points, arr, xi)

and so does this:

xi = (0.1, 9, 24, np.linspace(0, 0.3, 4))
result = interpn(points, arr, xi)

but not this:

xi = (0.1, 9, np.transpose(np.linspace(0, 30, 3)), np.linspace(0, 0.3, 4))
result = interpn(points, arr, xi)

As you can see, in the last case, the size of the last two arrays in xi is different. Is this kind of functionality not supported by scipy or am I using interpn incorrectly? I need this create a plot where one of the xi's is a parameter while the other is the horizontal axis.

1
Looks like you're not using interpn correctly... I'm assuming that points represents your grid, i.e., the "sampling points" in each of your four dimensions for the values that you know. arr holds these known values. But making them random means it's hard to check whether or not the interpolation is working. Try making them all equal instead, or better yet, linear in each of the four dimensions. xi should be the coordinates of the points at which you want to know the values of arr. xi should be an array with k rows, for k points, and 4 columns (4D data). - Praveen
Thanks Praveen! My question, however, is the following. Suppose I have data that depends on 4 variables: a, b, c, d. I want interpolate to return a 2D array which corresponds to a single value of a and b, and an array of values for c and d. However, The array size need not be the same. To be specific, my data comes from a transistor simulation. The current depends on 4 variables here. I want to plot a parametric variation. The number of points on the parameter is a lot less than the number of points for the horizontal axis. - Ashwith Rego
Next time, just edit your question directly, instead of adding a lot of information in a comment - Praveen
By the way, note that np.transpose(np.linspace(0, 30, 3)) does not make it into a column vector. Read about 1D arrays in numpy. You need to introduce a new dimension, so use np.linspace(0, 30, 3)[:, np.newaxis] instead. But in this case, you don't need this, as I show in my answer. - Praveen
Ugh the transpose was a mistake. I was meddling around with the code to see what would work and it crept into this post. Sorry about that! - Ashwith Rego

1 Answers

12
votes

I'll try to explain this to you in 2D so that you get a better idea of what's happening. First, let's create a linear array to test with.

import numpy as np

import matplotlib.pyplot as plt
from mpl_toolkits.mplot3d import Axes3D
from matplotlib import cm

# Set up grid and array of values
x1 = np.arange(10)
x2 = np.arange(10)
arr = x1 + x2[:, np.newaxis]

# Set up grid for plotting
X, Y = np.meshgrid(x1, x2)

# Plot the values as a surface plot to depict
fig = plt.figure()
ax = fig.gca(projection='3d')
surf = ax.plot_surface(X, Y, arr, rstride=1, cstride=1, cmap=cm.jet,
                       linewidth=0, alpha=0.8)
fig.colorbar(surf, shrink=0.5, aspect=5)

This gives us: surface plot of values

Then, let's say you want to interpolate along a line, i.e., one point along the first dimension, but all points along the second dimension. These points are not in the original arrays (x1, x2) obviously. Suppose we want to interpolate to a point x1 = 3.5, which is in between two points on the x1-axis.

from scipy.interpolate import interpn

interp_x = 3.5           # Only one value on the x1-axis
interp_y = np.arange(10) # A range of values on the x2-axis

# Note the following two lines that are used to set up the
# interpolation points as a 10x2 array!
interp_mesh = np.array(np.meshgrid(interp_x, interp_y))
interp_points = np.rollaxis(interp_mesh, 0, 3).reshape((10, 2))

# Perform the interpolation
interp_arr = interpn((x1, x2), arr, interp_points)

# Plot the result
ax.scatter(interp_x * np.ones(interp_y.shape), interp_y, interp_arr, s=20,
           c='k', depthshade=False)
plt.xlabel('x1')
plt.ylabel('x2')

plt.show()

This gives you the result as desired: note that the black points correctly lie on the plane, at an x1 value of 3.5. surface plot of interpolated points

Note that most of the "magic", and the answer to your question, lies in these two lines:

interp_mesh = np.array(np.meshgrid(interp_x, interp_y))
interp_points = np.rollaxis(interp_mesh, 0, 3).reshape((10, 2))

I have explained the working of this elsewhere. In short, what it does is to create an array of size 10x2, containing the coordinates of the 10 points you want to interpolate arr at. (The only difference between that post and this one is that I've written that explanation for np.mgrid, which is a shortcut to writing np.meshgrid for a bunch of aranges.)

For your 4x4x4x4 case, you will probably need something like this:

interp_mesh = np.meshgrid([0.1], [9], np.linspace(0, 30, 3),
                          np.linspace(0, 0.3, 4))
interp_points = np.rollaxis(interp_mesh, 0, 5)
interp_points = interp_points.reshape((interp_mesh.size // 4, 4))
result = interpn(points, arr, interp_points)

Hope that helps!