Scapy - retrieving RSSI from WiFi packets

Question

I'm trying to get RSSI or signal strength from WiFi packets. I want also RSSI from 'WiFi probe requests' (when somebody is searching for a WiFi hotspots).

I managed to see it from kismet logs but that was only to make sure it is possible - I don't want to use kismet all the time.

For 'full time scanning' I'm using scapy. Does anybody know where can I find the RSSI or signal strength (in dBm) from the packets sniffed with scapy? I don't know how is the whole packet built - and there are a lot of 'hex' values which I don't know how to parse/interpret.

I'm sniffing on both interfaces - wlan0 (detecting when somebody connects to my hotspot), and mon.wlan0 (detecting when somebody is searching for hotspots). Hardware (WiFi card) I use is based on Prism chipset (ISL3886). However test with Kismet was ran on Atheros (AR2413) and Intel iwl4965.

Edit1:

Looks like I need to access somehow information stored in PrismHeader: http://trac.secdev.org/scapy/browser/scapy/layers/dot11.py line 92 ?

Anybody knows how to enter this information? packet.show() and packet.show2() don't show anything from this Class/Layer

Edit2:

After more digging it appears that the interface just isn't set correctly and that's why it doesn't collect all necessary headers. If I run kismet and then sniff packets from that interface with scapy there is more info in the packet:

###[ RadioTap dummy ]###
  version= 0
  pad= 0
  len= 26
  present= TSFT+Flags+Rate+Channel+dBm_AntSignal+Antenna+b14
  notdecoded= '8`/\x08\x00\x00\x00\x00\x10\x02\x94\t\xa0\x00\xdb\x01\x00\x00'
  ...

Now I only need to set the interface correctly without using kismet.

Answer 1

Here is a valuable scapy extension that improves scapy.layers.dot11.Packet's parsing of present not decoded fields.

https://github.com/ivanlei/airodump-iv/blob/master/airoiv/scapy_ex.py

Just use:

import scapy_ex

And:

packet.show()

It'll look like this:

###[ 802.11 RadioTap ]###
  version   = 0
  pad       = 0
  RadioTap_len= 18
  present   = Flags+Rate+Channel+dBm_AntSignal+Antenna+b14
  Flags     = 0
  Rate      = 2
  Channel   = 1
  Channel_flags= 160
  dBm_AntSignal= -87
  Antenna   = 1
  RX_Flags  = 0

Answer 2

To summarize:

• signal strength was not visible because something was wrong in the way that 'monitor mode' was set (not all headers were passed/parsed by sniffers). This monitor interface was created by hostapd.

• now I'm setting monitor mode on interface with airmon-ng - tcpdump, scapy show theese extra headers.

Edited: use scapy 2.4.1+ (or github dev version). Most recent versions now correctly decode the « notdecoded » part

Answer 3

For some reason the packet structure has changed. Now dBm_AntSignal is the first element in notdecoded.

I am not 100% sure of this solution but I used sig_str = -(256 - ord(packet.notdecoded[-2:-1])) to reach first element and I get values that seems to be dBm_AntSignal.

I am using OpenWRT in a TP-Link MR3020 with extroot and Edward Keeble Passive Wifi Monitoring project with some modifications.

I use scapy_ex.py and I had this information:

802.11 RadioTap

  version   = 0

  pad       = 0

  RadioTap_len= 36

  present   = dBm_AntSignal+Lock_Quality+b22+b24+b25+b26+b27+b29

  dBm_AntSignal= 32

  Lock_Quality= 8

Answer 4

If someone still has the same issue, I think I have found the solution:

I believe this is the right cut for the RSSI value:

sig_str = -(256-ord(packet.notdecoded[-3:-2]))

and this one is for the noise level:

noise_str = -(256-ord(packet.notdecoded[-2:-1]))

Answer 5

The fact that it says "RadioTap" suggests that the device may supply Radiotap headers, not Prism headers, even though it has a Prism chipset. The p54 driver appears to be a "SoftMAC driver", in which case it'll probably supply Radiotap headers; are you using the p54 driver or the older prism54 driver?

Answer 6

I have similar problem, I set up the monitor mode with airmon-ng and I can see the dBm level in tcpdump but whenever I try the sig_str = -(256-ord(packet.notdecoded[-4:-3])) I get -256 because the returned value from notdecoded in 0. Packet structure looks like this.

 version   = 0
 pad       = 0
 len       = 36
 present   = TSFT+Flags+Rate+Channel+dBm_AntSignal+b14+b29+Ext
 notdecoded= ' \x08\x00\x00\x00\x00\x00\x00\x1f\x02\xed\x07\x05 
 .......